If you had the same stock of the blue solution as in the serial dilution simulation you did (1M solution), and you needed 10 mL of a solution that was 1.0x10-6 M, what volume of the blue stock solution would you need, and what volume of diluent would you need to reach 10 mL of the desired concentration

Answer: We start by doing a 1/10 serial dilution, using 100 µL of 1M solution into 900 µL of water, until we get a 1.0x10^-5M (0.00001M) solution. Then use 1 mL of this 1.0x10^-5M solution into 9 mL of water.

Explanation:

To answer this question, we must use the law of conservation of mass, which states: In every chemical reaction mass is conserved, this means the total mass of the reactants is equal to the total mass of the products. The law implies that mass can neither be created nor destroyed, but it can be transformed. For example, in chemical reactions, the mass of the chemical components before the reaction is equal to the mass of the components after the reaction. Therefore, during any chemical reaction and low-energy thermodynamic processes in an isolated system, the total mass of the reactants or starting materials must be equal to the mass of the products. This law is quite accurate for low-energy processes, such as chemical reactions.

So, if the solution to be used is 1M , and a 10 mL of a 1.0x10^-6M solution is needed, we use the following equation:

Initial concentration x initial volume = final concentration x final volume.

The initial concentration is 1M, the final concentration is 1.0x10^-6M and the final volume required is 10 mL.

1M x initial volume = 1.0x10^-6M x 10 mL

initial volume=  1.0x10^-5 mL= 0.01 µL of 1M solution.

Since the final volume is 10 mL, we have to add the difference in volume with water, which is 10 mL - 1.0x10^-5 mL= 9.99999 mL.

However, since 0.01 mL is a very small volume that is difficult to take, the best option in this case is to make serial dilutions.

Usually, we start from a concentrated solution and prepare a series of dilutions to the tenth (1:10) or half (1:2). In this way a series of solutions is obtained, related for example by a dilution factor of 10, i.e. 1/10; 1/100; 1/1000 and so on.

Here we can prepare a series of dilutions to the tenth, from 1M to 1.0x10^-6.

We start by doing a 1/10 dilution, using 100 µL of 1M solution into 900 µL of water. This is a 0.1M solution. Then we take 100 µL of it into 900 µL of water to get a 0.01M solution. We continue doing that until we get a 1.0x10^-6M (0.000001M) solution. This final solution is the desired concentration, however we need 10 mL of it, and actually we have 1 mL. So we can just take 1 mL of the 1.0x10^-5M solution into 9 mL of water:

1.0x10^-5M x 1 mL = 1.0x10^-6M x 10 mL.

Fresh milk has a pH of 6.
How do you think the pH
would change as it became
sour? Explain your answer.

The Water Cycle: Lesson
Mckenze Jelks
Which example best shows how the water cycle carries on energy transfer?
Choose the correct answer.
O a flooding river depositing silt on a floodplain
O a warm ocean current warming the air above it
O ocean water depositing sand particles on a shore
O water seeping through the soil and dissolving salts

nitrogen atom in NH3 has ___ shared electrons ​

what do you think will happen if there is no coal.

Draw the structure of the peptide DTLH, showing the backbone and side-chain atoms, at its isoelectric point. Draw the molecule on the canvas by choosing buttons from the Tools (for bonds and charges), Atoms, and Templates toolbars. Draw peptide molecule as zwitter ion.

what is the difference between fluorine and oxygen?

What type of chemical reaction is this? CH4 + O2 + CO2 + H20 ?

[24 points] A sample of soil has a total volume of 205 cm3. The soil mass when saturated is 361 g. A specific yield test was conducted on the soil by allowing the sample to drain for 24 hours. After drainage the sample mass was 295 g. The soil was then dried and weighed 284 g. What are the specific yield [8 points], specific retention [8 points], and porosity [8 points] of the sample

How many moles are in 3.30 x 1024 molecules of N2I6

HURRY PLEASE
If 12 grams of sodium reacts with 16 grams of chlorine, how much sodium chloride is Formed?
A. 4 g
B. 12 g
C. 28 g
D. 30 g

1. What is the molar mass of Al2S3?