Answer:
true
Explanation:
A cone penetration test was carried out in normally consolidated sand, for which the results are summarized below: Depth (m) Cone resistance, qc (MN/m2 ) 2.0 3.12 3.5 4.25 5.0 5.14 6.5 9.23 8.0 12.2 The average unit weight of the sand is 16.5 kN/m3 . Determine the friction angle at each depth using Eq. (3.52)
Answer:
hello your question is incomplete attached below is the missing equation related to the question
answer : 40.389° , 38.987° , 38° , 39.869° , 40.265°
Explanation:
Determine the friction angle at each depth
attached below is the detailed solution
To calculate the vertical stress = depth * unit weight of sand
also inverse of Tan = Tan^-1
also qc is in Mpa while σ0 is in kPa
Friction angle at each depth
2 meters = 40.389°
3.5 meters = 38.987°
5 meters = 38.022°
6.5 meters = 39.869°
8 meters = 40.265°
Question Completion Status:
The point of application of the total pressure on surface is
O a. None of the above
O b. Centroid of the surface
O c. Centre of pressure
Answer: c. Centre of pressure
Explanation:
Pressure is applied on a surface when a force is exerted on a particular point on that surface by another object when the two come into contact with each other.
The point where the pressure is applied is known as the centre of the pressure with the force then spreading out from this point much like an epicentre in an earthquake.
Consider a continuous-flow, indraft supersonic wind tunnel, which uses a vacuum pump to draw atmospheric air from outside of the wind tunnel building through a converging-diverging nozzle, to establish the supersonic flow in the test section. Assuming a standard day in Morgantown, WV (elevation of 961 feet) and a Mach number of 2.0 in the test section, compute the following:_____
a) The test section temperature
b) The test section pressure, assuming isentropic flow
c) The test section velocity
d) The change in the specific enthalpy of the air
Calculate the percentage of recyclables in high socioeconomic localities.
Answer:
The percentage of recycling in high socioeconomic localities is 11.02%.
Explanation:
Since in high socioeconomic localities, 10% of paper is recycled, 12% of plastic, 1.7% of fabrics, 1.2% of rubbers, 0.9% of metals, 3.5% of glass, 33% of food wastes, 35% soil and 1.9% miscellaneous, to determine the average recycling percentage the following calculation must be performed:
(10 + 12 + 1.7 + 1.2 + 0.9 + 3.5 + 33 + 35 + 1.9) / 9 = X
99.2 / 9 = X
11.02 = X
Therefore, the percentage of recycling in high socioeconomic localities is 11.02%.
A brake caliper is considered a suspension item.
True
False
PLEASE HELP THIS IS A TEST I WAS SUPPOSE TO DO 8 HOURS AGO.
An object has a width of 1.0 in. if you were to create a 1:4 scaled drawing of this object, what would the dimensions of the drawing be?
Convert the following measurement to their unit equivalents.
14.5 ft =___inch
15. 60 inch=___feet
16. 10 inch = __centimeter
17. 5 meter =__decimeter
18. 8 meter = ___feet
Explanation:
(1) 174 inch
(2)1 foot 3.6 inches
(3) 39.649 centimetre
(4)175 decimeter
(5)26.25 feet
In your own words how does an airplane take off?
Answer:
Explanation:
How does an aircraft take off?
They are lift, weight, thrust and drag. Lift pushes the airplane up. The way air moves around the wings gives the airplane lift. The shape of the wings helps with lift, too.
HOPE THIS HELPS!
The point of contact of two pitch circles of mating gears is called?
Answer:
the pitch point im pritty sure what is is
The point of contact of two pitch circles of mating gears is called the pitch point.
What is the pitch point?
A pitch point is where two pitch circles frequently come into touch. A common point of contact between two pitch circles of mating gears is called a pitch point. The pitch circle and is centered on the top of the teeth. Dedendum circle, also known as the root circle, is the circle traced through the base of the tooth.
The pressure angle, often known as the “tooth shape,” is the angle at which pressure from one gear's tooth is transferred to another gear's tooth. Pure rolling motion will occur at pitch point.
Therefore, it is pressure point.
Learn more about the pressure point, refer to:
https://brainly.com/question/2510654
#SPJ6
The bottom of a pan is made of a 4-mm-thick aluminum layer. In order to increase the rate of heat transfer through the bottom of the pan, a design was proposed for the bottom that consists of a 3-mm-thick copper layer sandwiched between two 2-mm-thick aluminum layers. Assume a perfect contact between the layers. Will the new design conduct heat better
Answer:
Yes, the new product will not conduct heat better
Explanation:
The bottom of the former product is made up of a 4mm thick aluminum layer
The new design is made up of two 2mm thick aluminum layer with a 3mm thick copper layer sandwiched in between.
These two materials are great conductors of heat.
As for copper, if one end is heated , the other ends rapidly reaches the same temperature, Copper is known as the best conductor of heat, that is, allows quick heat transfer. This ability of copper makes it highly used in applications where quick heat transfer is important, like the saucepans where rapid heat transfer is required.
As for aluminum, it is also a great heat conductor and twice as good as copper.
But the heat conductivity of copper is greater than aluminum and this will allow a faster heat transfer between the layers.
Were you surprised by the “pie data”? Is it true for you, your family, and your friends? Why or why not?
this is a coding question, and pie data is a misprint. It is actulaly big data.
Answer:
No because it is something to gain knowledge of peoples lives.
Answer: i was not suprised because, it is something all people need to know to gai knowledege about it.
what are material engineers trying to discover when they study different materials
Answer:
The Material engineers trying to discover when they study different materials is described below in complete detail.
Explanation:
Material engineers analyze various elements to discover the purpose and explanation of its existence, the chemical characteristics, how long it has stood there, and how it influences human life. The material engineer is an engineering exercise that concentrates to enhance human activity by investigating the environment and the diverse elements or elements it holds.
Bob would like to run his house off the grid, therefore he needs to find out how many solar panels and batteries he needs to buy.
The power output of a 250 W solar panel is p=250−10(t−5)2 watts for the average 10 hour day. He plans on using 12 V, 120 A⋅h batteries and would like to able to store 3 days worth of energy. Bob's house uses 1100 kW⋅h per month (30 days).
Answer:
stink
Explanation:
Effectively,how many valence electrons are there in each atom within q silicon crystal?
Answer:
Four valence electrons
Silicon is having an atomic number of 14 which means It has two electrons in its first shell, eight electrons in the second shell, and four electrons in the third shell.
Rigid bar ABC is supported by three symmetrically-positioned vertical rods, which are initially unstrained. After load P is applied, the normal strain in rods (2) is 0.0010 mm/mm. Determine the normal strain in rod (1) if there is a gap of 1.0 mm in the connection between rod (1) and the rigid bar at B. Report the strain in mm/mm
Answer:
The answer is below
Explanation:
The lengths of the rods are not given.
Let us assume the length of rod 1 = 1500 mm and the length of rod 2 = 800 mm
Solution:
The normal strain is defined as the change in member length δ divided by the initial member length L. The normal strain (ε) is:
ε = δ / L
δ = εL
For rod 1:
[tex]\delta_2=\epsilon_2 L_2\\\\\delta_2=0.0010\ mm/mm*1500\ mm=1.5\ mm[/tex]
The axial elongation of rod 2 is 1.5 mm. Since rigid bar ABC is attached to rod 2, the rigid bar move down by same amount.
The rigid bar moves down 1.8 mm but rods 1 will not be stretched by this amount. Because there is a gap between rod (1) and the rigid bar at B, the first deflection of 1 mm would not cause an elongation in rod 1. Therefore, the elongation in rods (1) is:
[tex]\delta_1=1.5\ mm-1\ mm=0.5\ mm[/tex]
The normal strain in rod 1 is:
[tex]\epsilon_1=\frac{\delta_1}{L_1} =\frac{0.5\ mm}{800\ mm} \\\\\epsilon_1=0.000625\ mm/mm[/tex]
(25%) A well-insulated compressor operating at steady state takes in air at 70 oF and 15 psi, with a volumetric flow rate of 500 ft3 /min, and compresses it to 60 psi. The power input to the compressor is 80 horsepower. Kinetic and potential energy changes from the inlet to exit can be neglected. Determine the exit temperature, in oR.
Answer:
You can look it up
Explanation: if you don't know what it is look it up on .
Describe how self-healing polymers could be useful in the construction of
plastic frames for glasses and sunglasses.
Answer:
This can be achieved through the use of a built-in fiber-optic network of cables that deliver light and heat energy to the point of breakage.
Explanation:
Self-healing polymers are materials designed to aid the internal healing of materials like plastics, and metals. Shape-memory materials used in the making of plastic frames for glasses and sunglasses allow these materials to snap back into shape when they crack.
This is possible because heat is needed to help a deformed material regain its shape. Built-in fiber-optic network of cables serve the purpose of delivering heat to the deformed or cracked area, thus helping them to regain their shape.
Please answer ASAP!!
How do we define energy efficiency?
А.) the ratio of the actual output energy to the input energy
B.) the ratio of power gain to power loss
C.) the product of input power and output power
D.) the sum of potential and kinetic energy
Answer:
a
Explanation:
that is what energy efficiency is
Assume that 50,000 yd3 of the soil from a local borrow pit in Rhode Island, with a water content of 13% and dry unit weight of 87 pcf, is to be delivered to a construction site for some repairs of highway in I-95. By the time it reaches the site, the water content is 9%. It will be compacted to a minimum of 90% of the modified Proctor maximum dry density. Determine the total amount of water (in pounds), that must be added to the soil to increase the moisture content to the optimum level. Assume a Gs
Answer:3000 yd3
Explanation:
so i got the 50000 divided it by 100 times that by 13 and got 4500 yd3
so now the soil is at 9 so i need to get the 4 percent back up so i yet again got 50000 yd3 and divided by 100 and times it by 9 to get 1500 yd3 to then minus my 1500 and 4500 yd3 and got 3000 yd3 i hope it is right.
Please answer ASAP!!
Which statement correctly describes why the electric pole has bent?
A.) Tensile stress acting on the pole caused it to bend.
В.) Compressive stress acting on the pole caused it to bend
С.) The force acting on the pole exceeded its yield strength.
D.) The force acting on the pole exceeded its compressive strength.
Answer:
С.) The force acting on the pole exceeded its yield strength.
Explanation:
Answer:
The correct answer is C. The force acting on the pole exceeded its yield strength.
Explanation:
I got it right on the Plato test.
What is a kind of useful car?
Considering how likely the risk is to affect the company’s profits is part of which component of risk management?
Risk identification
Risk assessment
Risk control
Risk mitigation
what is a car that self driving
Answer:
It is when a person don't have to drive, the car can move by itself. (That's what I think it is) Hopes it help :)
Explanation:
What is "Engineering"?
Consider one-dimensional heat conduction through a large plane wall with no heat generation that is perfectly insulated on one side and is subjected to convection and radiation on the other side. It is claimed that under steady conditions, the temperature in a plane wall must be uniform (the same everywhere). Is this claim reasonable
Answer:
YES, this claim reasonable
Explanation:
the temperature in a plane wall is uniform since no heat is penetrating into the large plane wall and therefore, there is no heat transfer from the wall under steady conditions,
This condition will be met only when there are no temperature differences within the wall and the the outer surface temperature of the wall is equal to the temperature of its surrounding.
Therefore, Yes, this claim is reasonable
Jumbo Eggs are the most commonly used size egg when making a recipe because they are the highest produced size egg?
True or
False
Answer:
True
Explanation:
Many chickens lay eggs of that size and eggs from chickens are the most commonly used
A three-phase transformer connection has a delta-connected secondary, and one of the transformers has been center-tapped to form a neutral conductor. The phase-to-neutral value of the center-tapped secondary winding is 120V. If the high leg is connected to a single-phase load, how much voltage will be applied to that load
Answer:
207.84 V will be applied to that load.
Explanation:
Given that;
The phase-to-neutral value of the center-tapped secondary winding is 120V
the high leg is connected to a single-phase load
voltage that will be applied to that load = ?
Now, the the high leg voltage will be 1.732 times the single phase center tapped voltage .
so
Load Voltage = 1.732 × 120V
Load Voltage = 207.84 V
Therefore, 207.84 V will be applied to that load.
Who developed the process of blueprinting?
A.
Michelangelo Buonerotti
B.
Raphael Sanzio
C.
Sir John Herschel
D.
Vitruvius
what is an unit resistance
Answer: Ohm Ω
Explanation:
The resistance can be defined as the hindrance offered to the flow of current. Lower the current the higher is the resistance. The SI unit of resistance is ohm Ω. When one ampere current flows from an object or wire the application of one volt of potential difference on it the resistance so produce is one ohm. Resistance can be achieved by the application of the certain gadgets in the circuit which can prevent the flow of excess current from devices and can prevent shock circuit.
what car has autopilot?
tesla lol how did you not know that?
Answer:
Tesla is a car that is able to drive automatically.
